Dental Digital X-Ray Imaging System Machine/Teeth Whitening Machine/Oral Camera

Description

Digital X-Ray Machine
Features:
1.) The tube voltage frequency of this machine is 30 KHz, and the tube current is 0.2 MA. The radiation
scope is at an angle of 24 degrees, located within a distance of 1.2 meters ahead.
2.) Toshiba 0.3mm x 0.3mm micro-focus tube
3.) No protective operation room is needed when installing the complete machine
4.) Flexible adjustment of position and angle of handpiece
5.) Compact in volume, light in weight, convenient for carrying
6.) Time is adjustable, high contrast of picture, imaging in focus
7.) There are vacuum components and high-pressure parts inside of the machine, so for your safety and
the maintenance of the machine
8.) The tube head is equipped with excellent radiation-shield protection (except the radial mouth, and
tests have shown that the radial index is zero. Safety is guaranteed.
9.) Non-film inspection and storage can be realized when corresponding to a sensor
Specifications
Voltage: 110v±10%
Power: 24V 8000MA
Charger: 110V, 50Hz
Tube current: 0.1mA
Rating: 60W
Frequency: 30 KHz
Exposure time: 1-9 seconds optional
Leak radiation: < 20μgy/h(12lb)
Focus Skin Distance: >20cm
Tube voltage: 60KV
Relative Humidity(RH) < 80%
Storage conditions: 5-40 degrees Celsius, relative Humidity
Net weight: 5.5 kg
Dimension: 47 x 42 x 19 cm
Content:
Main Unit x 1
Dental Film Position x 1
Charger x 1
English Manual x 1
Warranty Card x 1
Operation of the Main Unit
1. Upon receiving, open the box and check the product for possible damage during shipping.
2. Make sure the fittings on the encasement list are packaged within the box.
3. Connect the six-core cable (of the Main Unit) to the joint of the ball head and tighten the screw
4. After the Main Unit and ball head are perfectly fit together, plug in the international standard
electrical source, grounding is strongly recommended.
5. Turn on the Power; the pilot lamp will be light up.During this time, the digital tube of the main unit
will show the fore setting time. Now the equipment is in standby mode.
6. Setting the time (Skip to next step if unneeded) Use the "SET", "+", and" -" buttons to reset the time
as follows: press SET, the pilot lamp above is illuminated, the machine is now in the time setting
mode→then press "+" and" -" to set the time needed (time range is 0.5-9seconds); press set again when
the time is adjusted the light lamp is off. The equipment is now in standby mode.
7. Put the Tooth film plumb behind the tooth which is going to be taken picture, and be as close as possible (the smooth side stick to the tooth)
8. Keep the ball head plumb to the tooth projection position; Have the ball head, tooth, and tooth film steadily mutually plumb.
9. After positioning, use theEXP on the main Unit, the remote controller, or the button on the touch head tube to take pictures. The three methods have the same effect. (Notice: gently press)
10. After exposure to the tube, release the start button again (available in three ways) in case of an emergency to stop shooting and return to standby status. (At this point there was no output ray, so the dental films can be used again).
Repeat step 6 to reset the picturing time.To repeat the picturing process, please repeat steps 7 to 9.
11. Turn the power of the main unit off when the work is finished, press POWER, making sure the pilot
lamp is off. Don't keep the main unit long in standby mode.
Points for Attention
1.
Make sure the angle of film, tooth, and b
all head are properly aligned when taking a picture. Keep them steady until the last step of picturing;
making sure that there is no change in any of their positions.
2.
Remember to turn the power offwhen work is done.
3.
Change the battery if the remote controller loses its functioning or if the remote's distance is shorted.
4.
After turning the power on, wait one minute before taking pictures, this allows the ray to provide a
steady output.
5.
The equipment switches into protection mode automatically when the voltage is incorrect. If this
occurs, it will not be able to carry out the normal work of filming.
6.
When taking pictures, the EXP button could stop the objection and then the machine goes back to the
preparation mode.
7.
Use high quality tooth film and developing liquid to make clear pictures.
8. Handle the ball head gently while in use, so as not to damage the delicate component.
9.
Do not pull hard on the cable which connects the ball head to the main unit.
10.
The cable connecting the ball head to the main unit cannot bear the weight of the ball head, so do not raise the ball head by holding the cable, it will cause damage.
11.
We usually set the time between 3-8 seconds when taking pictures, but the actual time of ray output
is 0.2-0.5 seconds.
12.
If a situation occurs, preventing the machine from taking regular pictures, contact the seller to solve the problem instead of trying to service the product yourself.
13.
Keep the tooth film and the liquid in a proper place and use them within the shelf-life period. While, because the liquid is not allowed to ship by carrier normal, so we take it out before ship, look forward to your understanding.
14.
Development of films should be performed at temperatures ranging between 23-25 degrees Celsius to ensure the image quality.
15.
Other requests accordance with the scope of the technical parameters.
16.
Please read the manual carefully before using.
SHIPPING FROM US TO US ,FROM CHINA TO OTHER COUNTRIES
About X-ray machine battery problem, lithium battery inside needs to keep active and can’t be stored for a long time without usage,which can lead to power failure.If it is not used for a long time, they are advised to discharge properly, (turn on the screen or expose several times), then charge about one hour.
Warning: After turning on the machine, wait for 1 minute, the voltage can be stabilized before normal use
；
After each photo taking, you need to wait for the normal value to return before taking a normal photo
。
USB Intraoral Camera
Product Name: Oral Endoscope
Pixel: 100W
Brightness adjustment: 3-speed adjustment
Simultaneous connection terminal: 1
Light source: 6 LED light sources
Focus range: 10mm-20mm
Interface：computer and android
Lens waterproof: IPX5
Shell material: ABS
Feature:
1.100W high defidition camera,720P high definition transmission;
2.Six high bright cold light sources;
3.Three-speed brightness adjustment;
4.Both computers and mobile phones can be used;
5.Daily waterproofing of the lens.
Teeth Whitening Machine
Description
:
1.
Simple, light and handy molding design.
2.Freely to adjust to any angle position
3. Unique semi-circular head design, both arches whitened at the same time.
4.10 pcs high power LED, fan-cooled.
5.1-20 minutes adjustable timer, suitable for more brands tooth whitening gel.
6.Led screen shows all the information. All the operation is so easy.
7. It`s suitable for dental chair upright of 45~50 mm diameter.
CHARACTER
：
1.
The special wavelength and high density light
speed catalyze whitening gel.
2.
10 powerful LED tubes emit a high intensive cold blue
light with an output at 6000 MW/CM2.
3.
Special design, innocuous silica gel muzzle,
make sure stopping intersectional infection.
4.
The new model of power supply make sure steady
power output and long- time continuous working
even in some cities and places with mutative voltage.
5.
Time display
is suitable for human design, and
could shows treatment time to help
dentist master treating time and progress and
reduce the waiting time of patient.
TECHNICAL PARAMETERS：
1.
Power supply: AC100-240V/ 50-60HZ
2. Power: 36W， 12V/3A
3. Light size: 30x80mm
4. Power density: >6000MW/CM2
5. Light timing: 0～20 mins
6. Power instability: <1%
7. Working method: time output & continuous working
8. Coupling: polyester mono
wave
9.
Packing size: 64*24*8 cm
Weight:
3.7
K
G/pck
Packing list:
1.
Main unit--- 1pc.
2. Silicagel muzzle -- -
2
pc.
3. Power adaptor DC12V3A--- 1pc.
4. Operation manual ---1pc.
5. Shoring ---1set
6. Cross base---------- 1set
FDA Statement
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, you can bid on this item only if you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.
Seller name:Dentistworld
City State: SHENZHEN,China
Telephone number:0755-69985450
We accept PayPal Only! All payments must be made within 7 days after the auction ends. Non-paying bidders will be reported to eBay. Please don't buy an item if you can't/won't pay for it.
Paypal is the easiest way to pay for items on eBay. Please make sure your Paypal and eBay accounts have the same physical address used for delivery and the same e-mail address to ensure payment confirmation.
Shipping: Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.
If the item you received is damaged or defective,Please contact us immidately.We will free exchange or refund.
We will pay the return shipping costs if the product is defective or the return is a result of our error. If the item is returned for any other reason you are responsible for the return shipping charges.
You can return your purchase for up to 15 days from the date of delivery. No refund will be issued if the product shows signs of use. Returned package must be in the original packaging, everything must be in new condition, No missing parts.
Our guarantee does not cover accidental damage or wear of product caused by customer.Thank you very much for your understanding!
The goods you odered will be posted out in the second working day after the paymet has been made. (We will inform you via email if any delay occured due to holiday events.
General shipping time is between 7-12 working days. (After the shipping started, the order will be monitored and the track of the item will be posted on paypal. Shipping:Import duties,taxes and charges are not included in the item price or shipping charges.These charges are the buyer's responsibility.
Destination
Delivery Time
Working Days
7-10
10-15
15-25
25-40
>50
US
Item arrived
80%
10%
8%
1%
Refund
ASIA
Item arrived
30%
40%
20%
10%
Refund
EU
Item arrived
20%
20%
50%
10%
Refund
AU
Item arrived
30%
30%
20%
20%
Refund
other countries
Item arrived
5%
10%
10%
60%
--
You feedback is VERY important to us
Please leave us positive feedback, an positive feedback will be automatically left for you once we receive your full payment. Please leave us with any concerns prior to leave negative feedback, as we can only correct issues when we are aware of them. We understand the concerns and frustrations you might have, and will try our best to resolve the isuues.
Serivce is our #1 priority at BAISTRA!
If you contact us immediately after placing the order, we will make every effort to assist you with your change request. Unfortunately, we can not make changes or cancel an order once it has shipped.
We offer the best items at the best prices. We strive to exceed all your expectations and put a smile on your face. Your experience will be a pleasant and effortless one when you buy at BAISTRA. We stand behind our products and pride ourselves on OUTSTANDING customer service. We guarantee that you will be delighted with your purchase or we will gladly and promptly issue you a refund or make things right!
On May-31-17 at 03:29:20 PDT, seller added the following information: